Troubleshooting Installed Hard Disk Drives When you turn on your computer, you expect the system to start, load the operating system from the hard disk, and display the usual desktop or Step 7: Recovery If the PC still cannot read the disc, recover the computer. www.isobuster.com It used to be free but there's still a trial version you can download and use. This issue may occur with pre-recorded discs and with recordable (R) or rewritable (RW) discs. http://webjak.net/unable-to/unable-to-read-registry-windows-7.html
Sidebar: Connecting Front-Mounted Header Cables Is Trial by Error 429 My PC Card slots work, but a new PC Card drive I just plugged in isn't recognized. Open the DVD rom bay on your laptop. it showing only first time when i burned data. For more information about the ATA/IDE interface, see "The ATA/IDE Interface," Chapter 1.
It will read discs now, but I have to pull back that transport almost every time, and there was no dirt or debris in mine. I have 64 bit. Reply Marty March 20, 2016 at 4:01 am I have read all that you are posting but I have to same computer that im using my burned dvd rom on. If your computer has Windows XP and is still using the same software configuration, the computer might have a software program called PC-Doctor.
It depends a lot on exactly how you created that disc in the first place. too bad..>.> my dvd's were kept way back since that feature was not working but thanks a lot. Now, normally, a degraded disc will more commonly show a different type of error. You can google search this to find instructions, they're probably everywhere.
I've had the same problem sometimes. All this does is burn the data files to the disc and not create an audio disc. I am having the same problem. Report Leon- May 4, 2011 at 02:29 AM Thankyou!
Disc or DVD contains media content not supported by the player Not all home entertainment DVD players are capable of supporting and playing all the different formats of movie and audio External Blu-ray/DVD Drive unable to read new Blu-ray discs solved What allows you to delete files from hard drive disk, but you can't from a cd/dvd? (read for more info) solved I deleted the high and low filters and still can't get Sims to work. next time you boot your computer, the DVD reader will seek the correct centre ring on the DVD, and will then read it properly.
Old CD-ROM or early DVD drive - Some early CD-ROM drives and Generation 1 DVD drives (some of the first DVD drives released) do not support CD-R discs or CD-RW discs. http://webjak.net/unable-to/unable-to-read-local-eventlog-reason-the-event-log-file-has-changed-between-read-operations.html If several discs work but one does not, the disc is probably bad or is scratched. I tried almost every solution given on net, but at last I am not sure what made it working.. If it had been burned on a Mac putting back into a Mac showed all the files and vice versa.
If you have changed upgraded the operating system or have a computer that came with Windows Me (or earlier) you can search the Internet for free diagnostic utilities or take the So now I can copy to my HDD then enable the writer to reburn. If you're reading this book after your old hard disk has been packed off to the manufacturer for replacement, we can still help. http://webjak.net/unable-to/unable-to-read-mbr-in-virtual-partition-dll-windows-7.html Can't Change Contents of ATA/IDE Hard Drive 682 I can't partition an ATA/IDE drive.
Advanced Search Forum Windows Operating Systems Windows XP XP unable to read DVD-RW ?? I fixed it by deleting the drive in Device Manager and restarting the PC. Report jason999- Nov 3, 2012 at 10:41 AM I had the same problem but I could read a self burned DVD only once after reboot then I would have to reboot
THANK YOU. A good way to check whether the incompatibility problems lie with the originating software or with one of the other causes listed above is to test the same disc on several If it works, you are done. http://webjak.net/unable-to/unable-to-read-data-from-the-transport-connection-windows-mobile.html Determining Actual Drive Failure Has Occurred 193 My IEEE-1394a or USB drive is detected when I plug it into the rear of the computer, but not when I plug it into
any ideas u can think of what might be that site? this fixed my issue. Close the Properties window and select the CD Drive name. Lucia St.
Thank you so much for the solution. Use the following steps to read a data disc from a command prompt: caution: Use the following steps carefully. Drive not powered on. VERY IMPORTANT: comments that do not add to the discussion - typically spammy, off-topic, or content-free comments - will be removed.
Your cache administrator is webmaster. Helpful +40 Report Jason in Australia Nov 14, 2008 at 05:28 PM Try to turn off the vista's burning feature. I am now at a loss please can someone help me. A great nerd website that listed and ranked all cd's from Archie worthy to junk by longevity ect.
I have not changed anything. Step 2: Checking discs For the purposes of troubleshooting, get several discs that were manufactured from a record label or from a software company before you use this document. Buffer Underrun Problems 685 I can't copy (drag and drop) files to a CD-R or CD-RW disc. my cd & dvd drives can not read solved DVD drive won't read any CD DVD +R not being read by Windows 7/CD/DVD/RW Drive solved CD/DVD ROM DRIVE chooses disc to
PC Defrag & Scandisk hard drive Run Defrag and ScanDisk on the hard drive. You saved me a bunch of $$$. mine is working now........ It may be an old CD-ROM only drive.
Troubleshooting Disk Partitioning Problems 205 My new CD-mastering program doesn't recognize my writeable drive. Now I’m using a laptop with Windows 7 and when I insert those discs in its CD drive, I cannot see any of the files.